"I bought this to deal with difficult to reach screws. I now find myself using it often in place of a traditional screwdriver, for one important reason which is not obvious until you try using it: You can apply pressue onto the screw with one hand, whilst turning the screw with the other hand - at a stroke, you can apply twice the force that's possible using one hand to both apply pressure and turn. Wish I'd had one years ago. Should be a must for any toolkit."
"I bought this item to adjust the virtually inaccessible carburetor pilot screws on my motorcycle. An almost impossible job was completed in just a couple of minutes with ease. Very good Screwdriver, well made and supplied with a good range of bits. Well recommended for those odd awkward jobs you might encounter and a very useful asset in your toolbox."
"A cheap, simple but effective tool for getting at otherwise inaccessible screws and fixings. Every toolbox should have one for those occasions when no other tool can do the job. Also comes with a straight bit holder so can be used as a normal driver."
"Excellent for getting into tight spots...had to take some legs off Ikea kitchen units to squeeze new flooring underneath them. My smallest screwdriver would not fit but this angled one was great, easily removed screws and made life really easy for very little money!!"
"Simple I bought this to fit mud flaps, the book said I needed to remove parts of the car to fit them this little gem worked so well no need. I have used this in various situations and it has not let me down, good quality tool."
"Great bit of kit. I use it for screwing cornice down onto kitchen wall units where there isn't much space between the unit top and the ceiling.
As others have said: forget the handle and use with a cordless driver instead. Takes standard bits so even though the bits supplied aren't that hard wearing you can use the bits you normally use (in my case DeWalt)."
"This is an easy to use screwdriver. Be aware the angle is not fully 90 degrees though, and the front bit is quite bulky. So, if you are considering this for a very tight space, be careful. I would buy this again, but I'm sure I won't have to as it's great quality."
"Excellent purchase. Needed to get into some tight spaces with a screwdriver and this item fitted the bill. I ordered on line and the item as ready waiting for me a little later the same day. The staff were really professional and courteous."
"Needed a 90' or offset driver for a tricky job in a very confined space, this was just the job.
Bang it straight in your hand held drill - don't muck about with the ratcheted handle - if you're doing a tricky job round a corner that a normal driver won't fit into then your hand probably won't have room to twist round either! My knuckles very quickly told me switch to drill like other reviewers suggest!!
"Brought this to get into a right spot when fixing my integrated dishwasher while trying to avoid dismantling it further. However it has ended up as a regularly used item in my toolbox.
I have tried various flexible shaft drivers etc. in the past and they have all been next to useless but this is rugged, reliable and gives great grip and torque enabling you to really put some weight behind it.
Used it last week in a combi drill with a flat wood bit to get through a hollow wall joist for a cable with access through just the hole for the switch! Invaluable!
PROS Small and light Strong Adjustable thumb grip (just slides off and moves round) Good torque Works with power tools
CONS Shame you can't remove the hex shaft to allow even better access in small places, but that's not a deal breaker:)"
"Bought this to reach an impossibly located screw. The screwdriver performed the task easily and unwound the screw easily using the anti-clockwise turn of the handle transferred through a gear in the head of the tool. Put the screw back in turning the handle clockwise. The lug behind the gear can be turned to any angle to hold the driver in position or you can remove it completely if space is tight. Altogether a good addition to a toolbox."
"This was my last resort to try to unscrew the top of a very heavy pre-assembled desk so I could move it up some stairs. Some of the fixings were inaccessible even to stubby screwdrivers, but this did just the job perfectly, even though it was still a close fit. There was still some indentation on the drawer runners!
If it hadn't been for this tool that desk would have been an immovable object!"
"Used this to undo the grub screw on the back of a swan neck tap on my kitchen sink. The tap is too close to the wall for a stubby screwdriver so this was the next best thing, bit fiddly as the screw is pretty small and i couldnt see properly but it did the job, so still a lot cheaper than getting a plumber round!"