Top Rated Product

Product Reviews

25 x 25 x 25mm. High quality compression fitting for MDPE pipe. Suitable for use below ground on cold water services. All fittings have a co-polymer polypropylene body, nut and thrust ring, acetal grab ring and nitrile seal. High impact resistant body and nut enables absorption of thermal and mechanical stress. Excellent pressure resistance, tested to 48bar. Simple and quick to connect - no need to dismantle the connecter nor chamfer the pipe, just cut the pipe, lubricate the seal, undo the nut a few turns, insert the pipe liner/insert, push the pipe in as far as it will go, tighten the nut and its done! Comfortably exceeds the performance requirements of UK Water Bylaws Scheme. MDPE Fittings are WRAS approved, certificate number 0507060.

25 x 25 x 25mm. High quality compression fitting for MDPE pipe. Suitable for use below ground on cold water services. All fittings have a co-polymer polypropylene body, nut and thrust ring, acetal grab ring and nitrile seal. High impact resistant body and nut enables absorption of thermal and mechanical stress. Excellent pressure resistance, tested to 48bar. Simple and quick to connect - no need to dismantle the connecter nor chamfer the pipe, just cut the pipe, lubricate the seal, undo the nut a few turns, insert the pipe liner/insert, push the pipe in as far as it will go, tighten the nut and its done! Comfortably exceeds the performance requirements of UK Water Bylaws Scheme. MDPE Fittings are WRAS approved, certificate number 0507060.
Average Customer Rating:
4.5 out of 5
4.5
 out of 
5
(2 Reviews) 2
Open Ratings Snapshot
Rating Snapshot (2 reviews)
5 stars
1
4 stars
1
3 stars
0
2 stars
0
1 star
0
2 of 2(100%)reviewers would recommend this product.
Customer Reviews for FloPlast MDPE Equal Tee 25mm
Review 1 for FloPlast MDPE Equal Tee 25mm
Overall Rating: 
5 out of 5
5 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
5 out of 5
5 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
5 out of 5
5 out of 5
Would you recommend this product? Yes
Overall Rating: 
5 out of 5
5 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
5 out of 5
5 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
5 out of 5
5 out of 5
Good value
1 Apr 2012
By starcott
, Lancashire
"Simple to connect to the MDPE pipe. Good value when compared to other brands."
1 of 1 people found this review helpful.
Review 2 for FloPlast MDPE Equal Tee 25mm
Overall Rating: 
4 out of 5
4 out of 5
Value: 
4 out of 5
4 out of 5
Features: 
4 out of 5
4 out of 5
Performance: 
4 out of 5
4 out of 5
Reliability: 
4 out of 5
4 out of 5
Would you recommend this product? Yes
Overall Rating: 
4 out of 5
4 out of 5
Value: 
4 out of 5
4 out of 5
Features: 
4 out of 5
4 out of 5
Performance: 
4 out of 5
4 out of 5
Reliability: 
4 out of 5
4 out of 5
FloPlast are my preferred
7 Jan 2014
By Michael83
, Aberdeen
"Much prefer the floplast units to the more expensive plasson types.
Plasson fittings use an O ring which isn't compressed by the back up ring, so if the MDPE pipe is scored at all, they can leak.
These however use a flexible lip seal which is compressed by the ferrul and nut, creating a solid and water tight seal which can cope with most scratches on a pipe.
The only issue is that when making up short runs these will pull in the pipe, putting tension on other fittings in the line, so be careful.
Also, when disassembling, the seal and ring tend to fall out on the floor and need cleaned before reassembly, but thats a pretty minor point."