Product Reviews

Good quality, long lasting tile drill for wet cutting of marble and tiles. Longer drilling life with faster, free machining action.

Good quality, long lasting tile drill for wet cutting of marble and tiles. Longer drilling life with faster, free machining action.
Average Customer Rating:
3.333 out of 5
3.3
 out of 
5
(3 Reviews) 3
Open Ratings Snapshot
Rating Snapshot (3 reviews)
5 stars
1
4 stars
1
3 stars
0
2 stars
0
1 star
1
2 of 3(67%)reviewers would recommend this product.
Customer Reviews for Diamond Tile Drill 12 x 85mm
Review 1 for Diamond Tile Drill 12 x 85mm
Overall Rating: 
5 out of 5
5 out of 5
Value: 
4 out of 5
4 out of 5
Features: 
3 out of 5
3 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
4 out of 5
4 out of 5
Would you recommend this product? Yes
Overall Rating: 
5 out of 5
5 out of 5
Value: 
4 out of 5
4 out of 5
Features: 
3 out of 5
3 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
4 out of 5
4 out of 5
diamond core bit
19 Jun 2011
By chiz
, wirral
"bit cut through porsalin tiles no problem, used with water to keep bit cool"
Review 2 for Diamond Tile Drill 12 x 85mm
Overall Rating: 
4 out of 5
4 out of 5
Value: 
3 out of 5
3 out of 5
Features: 
3 out of 5
3 out of 5
Performance: 
4 out of 5
4 out of 5
Reliability: 
3 out of 5
3 out of 5
Would you recommend this product? Yes
Overall Rating: 
4 out of 5
4 out of 5
Value: 
3 out of 5
3 out of 5
Features: 
3 out of 5
3 out of 5
Performance: 
4 out of 5
4 out of 5
Reliability: 
3 out of 5
3 out of 5
Cut thick porcelain tiles
18 Dec 2013
By Goodfella
, Berkshire
"This cutter did a fine job making easy work through some thick porcelain tiles to allow me to then drill the block behind with a 12 mm bit to fit some rigifix plugs.
It did not need water, i just kept the speed low and it took no time.
To avoid these skimming all over the tile, Note that these are too small for a pilot, the trick to getting them to bite on target is to approach the material at an angle of say 45 degrees, then once through the glaze straighten up the drill and keep going.."
Review 3 for Diamond Tile Drill 12 x 85mm
Overall Rating: 
1 out of 5
1 out of 5
Value: 
1 out of 5
1 out of 5
Features: 
2 out of 5
2 out of 5
Performance: 
1 out of 5
1 out of 5
Reliability: 
1 out of 5
1 out of 5
Would you recommend this product? No
Overall Rating: 
1 out of 5
1 out of 5
Value: 
1 out of 5
1 out of 5
Features: 
2 out of 5
2 out of 5
Performance: 
1 out of 5
1 out of 5
Reliability: 
1 out of 5
1 out of 5
Warning
21 Apr 2010
By Freddie10
, Cambridge
"Not sure if I managed to keep the core drill cool enough as I managed to drill two hole in the floor tiles with no problem. I then tried to drill two holes in wall tiles, the first of which went fine but on the second the drill stopped working as it lost its cutting edge. This could have been my fault for not getting enough water on to the work area but always difficult on walls."