Product Reviews

40mm 92.5° Pushfit Bend

40mm 92.5° Pushfit Bend
Average Customer Rating:
2.5 out of 5
2.5
 out of 
5
(8 Reviews) 8
Open Ratings Snapshot
Rating Breakdown 8 reviews
5 stars
3
4 stars
0
3 stars
0
2 stars
0
1 star
5
3 of 8(38%)reviewers would recommend this product.
Customer Reviews for FloPlast 92.5° (87.5°) Bend 40mm
Review 1 for FloPlast 92.5° (87.5°) Bend 40mm
Overall Rating: 
5 out of 5
5 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
5 out of 5
5 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
5 out of 5
5 out of 5
Would you recommend this product? Yes
Overall Rating: 
5 out of 5
5 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
5 out of 5
5 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
5 out of 5
5 out of 5
Push. Fit. Waste fittings
29-May-2014
By
, Burton-on-Trent
"Very good item easy to use if you repair the pipe with a taper to enter the fitting as it should be done any way not like the review I read where the rubber o ring came out and water leaked.if you do the job correct or don't complain about the fitting when you have not prepared the job as it should be done."
Review 2 for FloPlast 92.5° (87.5°) Bend 40mm
Overall Rating: 
5 out of 5
5 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
5 out of 5
5 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
5 out of 5
5 out of 5
Would you recommend this product? Yes
Overall Rating: 
5 out of 5
5 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
5 out of 5
5 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
5 out of 5
5 out of 5
excellent fittings
25-Sep-2012
By
, northampton
"floplast fittings are very good value and extremely easy to use."
Review 3 for FloPlast 92.5° (87.5°) Bend 40mm
Overall Rating: 
5 out of 5
5 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
3 out of 5
3 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
5 out of 5
5 out of 5
Would you recommend this product? Yes
Overall Rating: 
5 out of 5
5 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
3 out of 5
3 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
5 out of 5
5 out of 5
Tight as a ducks
16-Aug-2012
By
, Hull
"After reading some of the reviews i was a little bit apprehensive about using these.
Anyway I bought some, I cut the wastepipe square, deburred inside and out, used a little lubrication, silicone grease or spit! And Bobs your uncle, absolutely fine. I cannot understand how you could have a problem.
Will deffo use again.
"
Review 4 for FloPlast 92.5° (87.5°) Bend 40mm
Overall Rating: 
1 out of 5
1 out of 5
Value: 
2 out of 5
2 out of 5
Features: 
1 out of 5
1 out of 5
Performance: 
1 out of 5
1 out of 5
Reliability: 
1 out of 5
1 out of 5
Would you recommend this product? No
Overall Rating: 
1 out of 5
1 out of 5
Value: 
2 out of 5
2 out of 5
Features: 
1 out of 5
1 out of 5
Performance: 
1 out of 5
1 out of 5
Reliability: 
1 out of 5
1 out of 5
Floplast 40mm pushfit elbow
12-Jun-2013
By
, South Shields
"This turned out to be the most timetaking 'quickfit' ever. Each time the elbow was fitted it leaked as the O-ring kept popping out - difficult to spot until water leaks out., It was used with new compatible Screwfit pipe correctly cut cleaned & lubricated."
Review 5 for FloPlast 92.5° (87.5°) Bend 40mm
Overall Rating: 
1 out of 5
1 out of 5
Value: 
1 out of 5
1 out of 5
Features: 
1 out of 5
1 out of 5
Performance: 
1 out of 5
1 out of 5
Reliability: 
1 out of 5
1 out of 5
Would you recommend this product? No
Overall Rating: 
1 out of 5
1 out of 5
Value: 
1 out of 5
1 out of 5
Features: 
1 out of 5
1 out of 5
Performance: 
1 out of 5
1 out of 5
Reliability: 
1 out of 5
1 out of 5
Garbage
12-Jun-2013
By
, yorkshire
"O ring push's out when inserting pipe, used silicone spray and de-burred pipe first.
Buy some proper fittings for the job and you'll have no leaks
"
Review 6 for FloPlast 92.5° (87.5°) Bend 40mm
Overall Rating: 
1 out of 5
1 out of 5
Value: 
1 out of 5
1 out of 5
Features: 
1 out of 5
1 out of 5
Performance: 
1 out of 5
1 out of 5
Reliability: 
1 out of 5
1 out of 5
Would you recommend this product? No
Overall Rating: 
1 out of 5
1 out of 5
Value: 
1 out of 5
1 out of 5
Features: 
1 out of 5
1 out of 5
Performance: 
1 out of 5
1 out of 5
Reliability: 
1 out of 5
1 out of 5
not fit for use
21-May-2012
By
, Northants
"fiting is so tight the rubber seal comes out when the pipe inserted, leading you to think the pipe has sealed properly when it has'nt, caused lots of grief when water leaked.
Will not use again, this applies to all Floplast fittings.
"
Review 7 for FloPlast 92.5° (87.5°) Bend 40mm
Overall Rating: 
1 out of 5
1 out of 5
Value: 
4 out of 5
4 out of 5
Features: 
3 out of 5
3 out of 5
Performance: 
1 out of 5
1 out of 5
Reliability: 
3 out of 5
3 out of 5
Would you recommend this product? No
Overall Rating: 
1 out of 5
1 out of 5
Value: 
4 out of 5
4 out of 5
Features: 
3 out of 5
3 out of 5
Performance: 
1 out of 5
1 out of 5
Reliability: 
3 out of 5
3 out of 5
push fit elbow
25-Apr-2012
By
, cirencester
"Cannot use with standard 40mm. waste - fitting too small. Why can't all fittings and waste pipes be compatible????"
Review 8 for FloPlast 92.5° (87.5°) Bend 40mm
Overall Rating: 
1 out of 5
1 out of 5
Value: 
4 out of 5
4 out of 5
Features: 
1 out of 5
1 out of 5
Performance: 
1 out of 5
1 out of 5
Reliability: 
1 out of 5
1 out of 5
Would you recommend this product? No
Overall Rating: 
1 out of 5
1 out of 5
Value: 
4 out of 5
4 out of 5
Features: 
1 out of 5
1 out of 5
Performance: 
1 out of 5
1 out of 5
Reliability: 
1 out of 5
1 out of 5
Very Disapointed
26-Apr-2010
By
, Chester
"On more than one of these fitting I had the o ring turn out of its grove. You only find out this when the bend leaks. On closer exanination the oring has a flash from the manufacturing process which prevents the smooth entree of the pipe. The pipe hangs up on this a pulle the oring out of its grove. I compared it with another make with no flash on the ID of the oring which worked fine. Hope thyis is of help. Very frustrating on a Sunday evening fixing leaks."