Top Rated Product

Product Reviews

Inspection Bends

Inspection Bends
Average Customer Rating:
4.5 out of 5
4.5
 out of 
5
(4 Reviews) 4
Open Ratings Snapshot
Rating Breakdown 4 reviews
5 stars
2
4 stars
2
3 stars
0
2 stars
0
1 star
0
4 of 4(100%)reviewers would recommend this product.
Customer Reviews for Tower Inspection Bends 20mm Black Pack of 1
Review 1 for Tower Inspection Bends 20mm Black Pack of 1
Overall Rating: 
5 out of 5
5 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
5 out of 5
5 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
5 out of 5
5 out of 5
Would you recommend this product? Yes
Overall Rating: 
5 out of 5
5 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
5 out of 5
5 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
5 out of 5
5 out of 5
Tower Plastic Inspecion Bend.
30 Nov 2015
By
, Manchester
" Does what it's made for, a thin gasket on inside of lid would be a bonus. Dependant on size of cables being used can be tight threading cables through but that applies to all inspection bends. "
Review 2 for Tower Inspection Bends 20mm Black Pack of 1
Overall Rating: 
5 out of 5
5 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
5 out of 5
5 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
5 out of 5
5 out of 5
Would you recommend this product? Yes
Overall Rating: 
5 out of 5
5 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
5 out of 5
5 out of 5
Performance: 
5 out of 5
5 out of 5
Reliability: 
5 out of 5
5 out of 5
TOWER INSPECTION BENDS 30mm BL
8 Sep 2011
By
, WORCESTERSHIRE
" HAD THESE FOR A SMALL JOB NO PROBLEM FITTING THEM AND USE THE SPECIAL GLUE TO SEAL THE JOINTS FROM ANY WATER GETING IN AND TO LOCK IT TIGHT,FOR A GOOD JOB DONE. "
Review 3 for Tower Inspection Bends 20mm Black Pack of 1
Overall Rating: 
4 out of 5
4 out of 5
Value: 
4 out of 5
4 out of 5
Features: 
3 out of 5
3 out of 5
Performance: 
3 out of 5
3 out of 5
Reliability: 
4 out of 5
4 out of 5
Would you recommend this product? Yes
Overall Rating: 
4 out of 5
4 out of 5
Value: 
4 out of 5
4 out of 5
Features: 
3 out of 5
3 out of 5
Performance: 
3 out of 5
3 out of 5
Reliability: 
4 out of 5
4 out of 5
Useful for certain application
7 Oct 2015
By
, Somerset
" Neat and secure solution to making a 90 degree bend in rigid conduit, but watch what you route through it - 2 x 2.5mm T&E cables will go through it, but only with care, to avoid damaging the insulation on the sharp internal edges. Still worth it for a neat finish, though. Single 2.5mm, or twin 1.5mm T&E thread through much better. "
Review 4 for Tower Inspection Bends 20mm Black Pack of 1
Overall Rating: 
4 out of 5
4 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
4 out of 5
4 out of 5
Performance: 
4 out of 5
4 out of 5
Reliability: 
4 out of 5
4 out of 5
Would you recommend this product? Yes
Overall Rating: 
4 out of 5
4 out of 5
Value: 
5 out of 5
5 out of 5
Features: 
4 out of 5
4 out of 5
Performance: 
4 out of 5
4 out of 5
Reliability: 
4 out of 5
4 out of 5
Just a little caution...
11 Nov 2013
By
, Northants
" The moulding has quite sharp internal edges so when feeding cable through you can actually strip the insulation if you try pulling too hard and fast.
Otherwise good value. "
4 of 4 people found this review helpful.